How Loud Is a 500 kW to 2000 kW Generator Set, and What Does ‘Soundproof’ Actually Mean?

Estimated read time 4 min read
  • This topic is empty.
Viewing 1 post (of 1 total)
  • Author
    Posts
  • #15231
    Avatar for adminadmin
    Keymaster

      ‘Soundproof’ is not a certified rating — the actual specification a hospital or commercial building should ask for is a measured dB(A) figure at a defined distance and load, since the same generator can sit anywhere from the mid-70s to the high-90s in decibels depending purely on which enclosure type it ships in. Getting this distinction right before ordering avoids the common problem of a technically compliant generator that still fails a building’s acoustic requirement once installed.

      Noise Varies by Enclosure, Not Just by Model

      MPMC’s own documentation places its containerised silent-type range from as low as 83.4 dB(A) at 1 metre at 75% load on the MCLS1250 SC up to 98 dB(A) at 1 metre at 75% load on an MCLS2000 open-type unit of comparable capacity — the same underlying engine and alternator platform, with enclosure type accounting for the majority of that 15 dB(A) spread. This is why a hospital or commercial buyer should specify the enclosure type explicitly rather than assuming a given power rating comes with a fixed noise level.

      MPMC super-silent containerised generator sets, part of a documented deployment demonstrating the platform’s acoustic enclosure design.

      Enclosure Type

      Series

      Typical Noise Profile

      Best Suited To

      Open Type

      OE

      No acoustic enclosure; highest noise output

      Fixed installations away from occupied buildings

      Economic Type

      SE

      Basic enclosure, moderate attenuation

      Cost-sensitive standby duty, non-sensitive sites

      Silent Type

      SR2

      Noise reduction to 35 dB(A) or below at rated conditions

      Noise-sensitive commercial and light-industrial sites

      Containerized Super Silent (SC)

      SC

      83.4-91 dB(A) @1m @75% load depending on model

      Hospitals, data centres, and buildings near occupied space

      Rental Type

      SR (AU/EU)

      Super-silent containers to AU/EU rental standard

      Temporary hospital or commercial standby contracts

      Two Documented Buildings, Two Different Measurement Points

      MPMC’s 4 MW hospital critical-load backup installation in New Zealand documents 85 dB(A) at 1 metre at full load in a 40HC super-silent container, while a separate 3 MW commercial buildings project, also in New Zealand, documents 75 dB(A) at 7 metres at 100% load using Doosan DP222LC engines in 20HC super-silent containers — a useful reminder that a noise figure is only meaningful alongside the distance it was measured at, since a lower dB(A) figure at a longer distance is not automatically a quieter machine than a higher figure measured close to the enclosure.

      Project

      Building Type

      Capacity

      Noise Rating

      Measurement Point

      Hospital Critical Load Backup, New Zealand

      Hospital

      4 MW

      85 dB(A) @100% load

      1 metre from enclosure

      Commercial Buildings, New Zealand

      Commercial

      3 MW

      75 dB(A) @100% load

      7 metres from enclosure

      MPMC silent and economic-type generator sets side by side, illustrating the enclosure difference behind MPMC’s noise ratings.

      How the Rating Is Actually Verified

      Every containerised unit passes through full-load testing at 0%, 25%, 50%, 75%, 100%, and 110% of rated output inside a CNAS-certified test room, and the noise figures MPMC publishes are measured during this process rather than estimated from the enclosure’s design specification — meaning a buyer can request the actual test record for their specific unit rather than relying on a catalogue figure that may reflect a best-case build.

      Specifying the Right Enclosure for a Hospital or Commercial Site

      A hospital’s acoustic requirement is usually driven by proximity to wards or outdoor patient areas, while a commercial building’s requirement more often comes from a local noise ordinance measured at the property line rather than at the enclosure itself — meaning the correct comparison point (1 metre versus a longer property-line distance) should be established with the acoustic consultant or local authority before the enclosure type is finalised, since specifying against the wrong distance can result in an enclosure that is quieter than required, at unnecessary cost, or louder than compliant.

      Questions to Ask About Generator Set Noise Ratings

      • Request the dB(A) figure alongside the exact measurement distance and load percentage it was taken at

      • Confirm which enclosure type (SC, SR2, or rental super-silent) the quoted noise figure applies to

      • Ask for the factory noise test record for your specific unit, not a general catalogue figure

      • Establish whether your acoustic requirement is measured at the enclosure or at a property line

      • Confirm noise performance at your actual expected operating load, not only at 100% or 75%

      • Request a documented reference project with a comparable noise requirement and measurement method

      https://www.mpmc-china.com/
      MPMC Powertech Corp.

    Viewing 1 post (of 1 total)
    • You must be logged in to reply to this topic.